au.\*:("STREPPEL, A. H")
Results 1 to 18 of 18
Selection :
Tolerance reasoning and set-up planning for brakeformingDE VIN, L. J; STREPPEL, A. H.International journal, advanced manufacturing technology. 1998, Vol 14, Num 5, pp 336-342, issn 0268-3768Article
Advances in sheet metal forming applicationsSTREPPEL, A. H; KLINGENBERG, W; SLINGH, U. P et al.International journal of machine tools & manufacture. 2008, Vol 48, Num 5, issn 0890-6955, 128 p.Serial Issue
Condition-based maintenance in punching/blanking of sheet metalKLINGENBERG, W; DE BOER, T. W.International journal of machine tools & manufacture. 2008, Vol 48, Num 5, pp 589-598, issn 0890-6955, 10 p.Article
The generation of bending sequences in a CAPP system for sheet-metal componentsDE VIN, L. J; DE VRIES, J; STREPPEL, A. H et al.Journal of materials processing technology. 1994, Vol 41, Num 3, pp 331-339, issn 0924-0136Article
Numerical product design : Springback prediction, compensation and optimizationMEINDERS, T; BURCHITZ, I. A; BONTE, M. H. A et al.International journal of machine tools & manufacture. 2008, Vol 48, Num 5, pp 499-514, issn 0890-6955, 16 p.Article
Suitability of sheet bending modelling techniques in CAPP applicationsSTREPPEL, A. H; DE VIN, L. J; BRINKMAN, J et al.Journal of materials processing technology. 1993, Vol 36, Num 3, pp 329-356, issn 0924-0136Article
Tolerancing and sheet bending in small batch part manufacturingDE VIN, L. J; STREPPEL, A. H; KALS, H. J. J et al.CIRP annals. 1994, Vol 43, Num 1, pp 421-424, issn 0007-8506Article
Design study of the geometry of a punching/blanking toolSINGH, U. P; STREPPEL, A. H; KALS, H. J. J et al.Journal of materials processing technology. 1992, Vol 33, Num 4, pp 331-345, issn 0924-0136Conference Paper
The influence of material behaviour in air bending of steel sheetDE VIN, L. J; STREPPEL, A. H; KALS, H. J. J et al.European journal of mechanical and environmental engineering. 1997, Vol 42, Num 1, pp 19-23, issn 1371-6980Article
Increasing of the drawing depth using tailor rolled blanks-Numerical and experimental analysisMEYER, A; WIETBROCK, B; HIRT, G et al.International journal of machine tools & manufacture. 2008, Vol 48, Num 5, pp 522-531, issn 0890-6955, 10 p.Article
The effect of ultra-low frequency pulsations on tearing during deep drawing of cylindrical cupsALI, S; HINDUJA, S; ATKINSON, J et al.International journal of machine tools & manufacture. 2008, Vol 48, Num 5, pp 558-564, issn 0890-6955, 7 p.Article
Development of general multivariable run-by-run control methods with application to a sheet metal forming processRZEPNIEWSKI, Adam K; HARDT, David E.International journal of machine tools & manufacture. 2008, Vol 48, Num 5, pp 599-608, issn 0890-6955, 10 p.Article
Numerical modeling of advanced materialsMEINDERS, T; PERDAHCIOGLU, E. S; VAN RIEL, M et al.International journal of machine tools & manufacture. 2008, Vol 48, Num 5, pp 485-498, issn 0890-6955, 14 p.Article
Determination of the flow stress of magnesium AZ31-O sheet at elevated temperatures using the hydraulic bulge testKAYA, S; ALTAN, T; GROCHE, P et al.International journal of machine tools & manufacture. 2008, Vol 48, Num 5, pp 550-557, issn 0890-6955, 8 p.Article
Virtual manufacturing for press line monitoring and diagnosticsNG, Amos H. C; ADOLFSSON, Josef; SUNDBERG, Martin et al.International journal of machine tools & manufacture. 2008, Vol 48, Num 5, pp 565-575, issn 0890-6955, 11 p.Article
Modelling and control of the air bending processLUTTERS, D; STREPPEL, A. H; KALS, H. J. J et al.World congress on intelligent manufacturing processes & systems. 1997, pp 473-478Conference Paper
Process planning in small batch sheet metal part manufacturingSTREPPEL, A. H; LUTTERS, D; KALS, H. J. J et al.World congress on intelligent manufacturing processes & systems. 1997, pp 467-472Conference Paper
The use of product information structures in design and process planningLUTTERS, D; STREPPEL, A. H; KALS, H. J. J et al.World congress on intelligent manufacturing processes & systems. 1997, pp 479-484Conference Paper